EMA spread
Last updated
Last updated
This strategy is based on EMA, enabling Gunbot to buy when prices start moving up - indicated by the spread between fast and slow EMA decreasing. Selling takes places when prices start moving down again, indicated by the spread decreasing again.
The spread is calculated each cycle by subtracting the lowest EMA value from the highest EMA.
To refine this strategy, other indicators are available to be used as confirmation for both buying and selling. For example you could have Gunbot buy when the EMA spread starts decreasing and RSI is below 30.
Gain protection is optional for this strategy.
Be aware that this can lead to sell orders below your break-even point.
Example of how trading with this strategy can perform. Details and settings.
__
The infographic below describes what triggers trades with this strategy.
Following settings options are available for EMASPREAD and can be set in the strategy configurator of the GUI or the strategies section of the config.js file.
These settings are global and apply to all pairs running this strategy. When you want a specific parameter to be different for one or more pairs, use an override at the pair level.
Using the BUY_METHOD and SELL_METHOD parameters you can combine different methods for buying and selling. This strategy page assumes both BUY_METHOD and SELL_METHOD are set to EMASPREAD. Accepted values are all strategy names as listed here.
Buy settings are the primary trigger for buy orders. These parameters control the execution of buy orders when using EMASPREAD as buy method.
Set this to false to prevent Gunbot from placing buy orders.
"Never Buy Above". Use this to only allow buy orders below the last sell rate.
This sets the minimum percentage difference between the last sell order and the next buy. The default setting of 0 disables this option.
When set to 1, Gunbot will only place a buy order when the strategy buy criteria meet and price is at least 1% below the last sell price.
With this setting enabled, Gunbot will try to take any buy chance between the strategy entry point and your setting for TBUY_RANGE.
As soon as the ask price drops below the upper border of this range (called "Take Buy"), it will trail down with a range of TBUY_RANGE and place a buy order as soon as the ask price crosses up "Take Buy". Confirming indicators in use are respected.
Normal strategy buy orders are still possible while using TAKE_BUY.
This option should not be used together with reversal trading.
This sets the buy range for TAKE_BUY.
When set to 0.5, the initial trailing stop is set 0.5% above the entry point defined by BUY_LEVEL.
This sets entry point for TAKE_BUY at a percentage below the lowest EMA.
When you set this to 1, the entry point will be set 1% below the currently lowest EMA.
Sell settings are the primary trigger for sell orders. These parameters control the execution of sell orders when using EMASPREAD as sell method.
Set this to false to prevent Gunbot from placing sell orders.
With this setting enabled, Gunbot will try to take any possible profit between the break-even point and your strategy exit point. This can be useful, for example, on days where the markets move very slowly.
It works by trailing prices upwards between the break-even point and the strategy exit point, with a configurable range for trailing: TP_RANGE. A sell order will be placed when the trailing stop limit is hit or strategy sell conditions are reached. Confirming indicators in use are respected.
Sells at minimal loss are possible when using TAKE_PROFIT, acting as a sort of mini stop loss.
This option should not be used together with reversal trading or DOUBLE_CHECK_GAIN
This sets the sell range for TAKE_PROFIT.
When set to 0.5, the initial trailing stop is set 0.5% below the break-even point.
Enable this to only allow sell orders above the break-even point.
Disable this to allow sell orders below the break-even point.
This sets the minimum target for selling when DOUBLE_CHECK_GAIN is enabled.
Relevant indicators for trading with EMA spread
These settings have a direct effect on trading with EMASPREAD.
This sets the candlestick period used for trading, this affects all indicators within the strategy.
Only use supported values.
Setting a short period allows you to trade on shorter trends, but be aware that these will be noisier than longer periods.
Set this to the amount of candlesticks you want to use for your slow EMA. The closing price for each candle is used in the slow EMA calculation.
For example: when you set PERIOD to 5, and want to use 2h for slow EMA – you need to set EMA1 to 24 (24 * 5 mins).
Set this to the amount of candlesticks you want to use for your medium EMA. The closing price for each candle is used in the fast EMA calculation.
For example: when you set PERIOD to 5, and want to use 1h for medium EMA – you need to set EMA2 to 12 (12 * 5 mins).
Sets the minimum percentage difference between slow and fast EMA for EMASPREAD.
When set to 1, the spread must reach at least 1% before EMASPREAD can trigger a buy or sell.
Parameters to configure additional trailing for various types of orders. Trailing works just like it does for the TSSL strategy, the difference being the starting point of trailing.
Orders resulting from trailing are only placed when the main strategy criteria are met, and confirming indicators (if any) allow the order. All these conditions must occur in the same cycle.
Because this strategy trades in rounds where emaspread decreases in a specific cycle, it is not recommended to use additional trailing for normal buy and sell orders. Trades will only happen when both the trailing stop and strategy signal happen in the same round.
TrailMeThe following parameters in config.js have no function for this strategy and act as placeholder.
Parameter
Description
ATRX
Placeholder.
ATR_PERIOD
Placeholder.
BUYLVL1
Placeholder.
BUYLVL2
Placeholder.
BUYLVL3
Placeholder.
BUYLVL
Placeholder.
BUY_RANGE
Placeholder.
DISPLACEMENT
Placeholder.
EMASPREAD
Placeholder.
FAST_SMA
Placeholder.
ICHIMOKU_PROTECTION
Placeholder.
HIGH_BB
Placeholder.
KIJUN_CLOSE
Placeholder.
KIJUN_PERIOD
Placeholder.
KIJUN_STOP
Placeholder.
KUMO_CLOSE
Placeholder.
KUMO_SENTIMENTS
Placeholder.
KUMO_STOP
Placeholder.
LEVERAGE
Placeholder.
LONG_LEVEL
Placeholder.
LOW_BB
Placeholder.
MACD_LONG
Placeholder.
MACD_SHORT
Placeholder.
MACD_SIGNAL
Placeholder.
MAKER_FEES
Placeholder.
MEAN_REVERSION
Placeholder.
PP_BUY
Placeholder.
PP_SELL
Placeholder.
PRE_ORDER_GAP
Placeholder.
PRE_ORDER
Placeholder.
RENKO_ATR
Placeholder.
RENKO_BRICK_SIZE
Placeholder.
RENKO_PERIOD
Placeholder.
ROE_CLOSE
Placeholder.
ROE_LIMIT
Placeholder.
ROE_TRAILING
Placeholder.
ROE
Placeholder.
SELLLVL1
Placeholder.
SELLLVL2
Placeholder.
SELLLVL3
Placeholder.
SELLLVL
Placeholder.
SELL_RANGE
Placeholder.
SENKOUSPAN_PERIOD
Placeholder.
SHORT_LEVEL
Placeholder.
SLOW_SMA
Placeholder.
TENKAN_CLOSE
Placeholder.
TENKAN_PERIOD
Placeholder.
TENKAN_STOP
Placeholder.
TSSL_TARGET_ONLY
Placeholder.
USE_RENKO
Placeholder.
